Scaffolds

Tipos de Andaimes:

Multidirectional Scaffold

The ESTAFLEX multidirectional scaffolding has the best cost/benefit ratio among the ESTAF scaffolding as it is faster to assemble due to the system of fitting the posts with the diagonals and crossbars. It is made up of 1 ½” galvanized tubes with a 3.00mm wall and a wide range of accessories to meet different needs.

Tube & Clamp Scaffold

Tubes and clamps. Hot dip galvanized steel tubes with seam, nominal diameter of 1 ¹/², external diameter of 48.25 mm and minimum wall thickness of 3.00 mm. Cut to the required lengths of 1.00 mm and 6.00 mm, with a module of 25 cm.

Multidirectional Modular Ladder

Access element to scaffolding or service areas.

Metal beam

Safely replaces wooden planks. They are manufactured with two metallic U-shaped sheet metal profiles, connected by a vertical tube with a weld bead, allowing the attachment of other beams and/or forms for easy storage, takes up little space and can be palletized to facilitate transport.

VT12″ Trellised Metal Beam

Used as the main beam, with good resistance for larger spans and overhangs.

With 30.48cm high, 7.62cm thick and modulations ranging from 2.00m to 6.00m.
Permissible moment: 1200kgfm / Weight: 15kg/m

3” Metal Beam

Used as a secondary framework, that is, they are mainly prepared to receive the formwork panels for pillars, beams and slabs.

With 7.62cm high, 7.62cm thick and modulations ranging from 1.50m to 3.50m.
Permissible moment: 180kgfm / Weight: 6.50kg/m

4” Metal Beam

Used as main and/or secondary beam.

With 10.16cm high, 7.62cm thick and modulations that vary from 1.50m to 4.50m.
Permissible moment: 380kgfm / Weight: 8.50kg/m

6” Metal Beam

Used as the main beam, with larger spans and withstanding greater loads.

With 15, 24 cm high, 7.62 cm thick and modulations that vary from 1.50 m to 4.50 m.
Admissible moment: 800kgfm / Weight: 15kg/m

Shoring

Building Framing Tower, Framing Tower, Triangle and Trapezoid Modulated elements, manufactured in galvanized steel, with options for fitting with or without pins, with a small variety of basic elements and a single way of assembly, simplifies its execution, making it faster, avoiding errors. They can form triangular, square, rectangular or diamond shoring towers. They are widely used in scaffolding slabs and small and large beams. Load capacity of 5.0 tf/post, allows bracing with tubular and clamps, as required by the project.

Shoring Light

The metallic strut consists of an external base steel tube, with a nominal diameter of 2″, inside which there is a flute tube with a nominal diameter of 1 ¹/²”, which allows for telescopic adjustment every 10 cm and a glass of internal thread for millimetric adjustment.

Parts

Fixing Pin

It should be inserted into the flute tube hole, for regulation of 10 to 10 cm.

Shielded Cup

Cast piece, with internal thread for adjustment up to 8 cm.

Screwless pitchfork

Adapts to the end of the steel prop for beam fitting.

Crosshead (optional)

Indicated in cases where a larger support area is required for the bottom of the formwork and beams.

Form

Estaf's metallic forms are classified as reusable, as they can be used more than once, that is, reuse follows statistical precepts of wear and tear, thus intended for large repetitions of use.

Metallic

They are made up of SAE 1008/1010 modulated steel panels, with a 6 mm phenolic sheet lining and the various assembly accessories. It can be used in the construction of houses and buildings.

Accessories

They are the auxiliary elements that are part of the set of equipped formwork whose main objective is to connect the parts providing greater adaptation to the assembly.